Termination resistor calculator: series, parallel, Thevenin and AC
A driver of 45 Ω on a 50 Ω line needs about 6.80 Ω in series; a 50 Ω line terminated to 1.3 V from 3.3 V needs 130 Ω up and 82.0 Ω down. This calculator sizes series, parallel, Thevenin and AC (RC) termination for a single-ended line from TI's application notes, picks the stocked values, shows the reflection that is left on each edge, and draws the receiver's step response with and without it.
Series: one resistor at the driver, so the driver plus the resistor equal Z0 and the reflection from an open receiver is absorbed when it returns. Parallel: a resistor to ground at the far end, equal to Z0. Thevenin: two resistors at the far end, together Z0, that also set a DC level. AC: a resistor and capacitor in series at the far end, matched during edges and drawing no DC.
The characteristic impedance of the trace or cable, in Ω: 50 Ω is the usual single-ended target. The microstrip and coplanar calculators give it for a PCB trace.
The driver's output impedance while pulling up (the rising edge), in Ω, from its datasheet or IBIS model. SCAA080 Table 1 gives 45 Ω for the CDCx706 at 3.3 V on a 50 Ω line.
The output impedance while pulling down (the falling edge), in Ω. Often a few ohms below the pull-up: 42 Ω for the CDCx706 at 3.3 V.
The driver's swing, in V: the step the figure launches, and the high level a parallel resistor dissipates at.
The resistor series offered. E24 is the 5 % range; E96 the 1 % range.
- Series resistor R_S = Z0 − Z_out
- 6.50 Ω exact; fit 6.80 Ω (E24)
- Source reflection, rising edge
- +0.018 (Z_out 45.0 Ω + R_S)
- Source reflection, falling edge
- -0.012 (Z_out 42.0 Ω + R_S)
- Where it goes
- at the driver pins; the receiver end stays open
How this is calculated
Standard: TI SNLA027B (AN-807), Equations 14 and 16; TI SCAA080A §2 and Table 1; TI SNAA377 §3.1 Equations 1–4 and §4.1.1; TI SNLA034B (AN-903) §4 and §5 Equation 1
- SNLA027 Equations 14 and 16 (p. 6), the voltage reflection coefficients of the load and the source. For series termination R_S is the driver impedance plus the series resistor; for the far-end schemes R_L is the termination.
- SCAA080 §2: "The sum of the driver impedance Zout and RS should be close to the transmission line impedance Z0"; SNAA377 §4.1.1: Z_O = R_O + R_S. The mean of the pull-up and pull-down impedances is this page's choice; SCAA080 asks for "a good matching ... for PU and PD". Floored at zero.
- SNLA034 §4: R_T "is typically chosen to be equal to ZO. When over-termination is used RT is typically chosen to be up to 10% larger than ZO." The power, with D the fraction of time high, is derived.
- SNAA377 Equations 1 and 2 (§3.1), solved for the two resistors. The note's Equations 3 and 4 check 130 Ω and 82 Ω from 3.3 V as "≈ 50Ω" and "≈ 1.3V". The standing power V_CC²/(R_TOP + R_BOTTOM) is derived.
- SNLA034 Equation 1 (§5), with t_d the one-way delay: "CT ≤ (Cable round trip delay) / ZO", and "the resulting RC time constant should be less than or equal to 10% of the unit interval (TUI)".
- The lattice of SNLA027 summed at the receiver: the n-th arrival, at (2n + 1) one-way delays. It converges to the DC divider V·R_L/(Z_S + R_L). Used for the figure.
Assumptions
- A single-ended, lossless, uniform line with resistive ends; the receiver is an open circuit and its capacitance is not modelled.
- The driver is a resistance: the mean of its pull-up and pull-down impedances for the far-end schemes and the figure, each edge separately for the series residuals.
- AC termination is drawn with the capacitor as a short during the edge, as SNLA034 describes it.
- Power figures are DC averages. Stocked values are the nearest in the chosen series, each resistor rounded on its own.
What it computes
A line needs terminating when its delay is long against the edge — the critical-length calculator decides that — and then one of four arrangements absorbs the wave that would otherwise bounce between the ends. TI's AN-807 (SNLA027) gives the quantity all of them work on, the voltage reflection coefficient, as Equation 14 for the load, ρL = (RL − R0)/(R0 + RL), and Equation 16 for the source. A matched end has ρ = 0 and sends nothing back. The calculator sizes the resistor for the scheme you choose, reports what is still reflected with the value you can buy, and draws the receiver's step response by the same note's lattice method.
Series termination puts one resistor at the driver. SCAA080: "The sum of the driver impedance Zout and RS should be close to the transmission line impedance Z0", and SNAA377 writes the same rule as ZO = RO + RS. The wave leaves at half amplitude, doubles at the open receiver, and is absorbed when its reflection returns to a matched source. Drivers rarely pull up and down with the same impedance, so the calculator uses the mean of the two and reports each edge's residual reflection; SCAA080 asks for "a good matching to the transmission line impedance for PU and PD" without saying how.
The far-end schemes match the receiver instead. Parallel termination is a resistor equal to Z0 to ground, or, per SNLA034, "up to 10% larger". Thevenin termination splits it into a pair whose parallel combination is Z0 and whose ratio sets a DC level, SNAA377's Equations 1 and 2. AC termination puts a capacitor in series with the resistor so no DC flows, sized by SNLA034's Equation 1, CT ≤ round-trip delay ÷ Z0.
Worked example: a clock buffer on a 50 Ω trace
The calculator's defaults: the CDCx706/x906 at 3.3 V on a 50 Ω line, with the pull-up and pull-down impedances SCAA080 measures in Table 1.
Driver, CDCx706 at 3.3 V pull-up 45 Ω, pull-down 42 Ω (SCAA080 Table 1) R_S = Z0 − mean(Z_out) 50 − 43.5 = 6.50 Ω Nearest E24 = 6.80 Ω ρS, rising (45 + 6.8 − 50)/(45 + 6.8 + 50) = +0.018 ρS, falling (42 + 6.8 − 50)/(42 + 6.8 + 50) = -0.012 Table 1's 5 Ω, rising edge (45 + 5 − 50)/(45 + 5 + 50) = +0.000
Both edges come within 1.8 % of a match with the stocked 6.80 Ω. SCAA080's own proposal for this row is 5 Ω, which leaves +0.000 on the rising edge: a difference of no practical weight on this line.
SCAA080's table against Z0 − Zout
The note proposes a series resistor for four line impedances at two supplies. Set beside the rule the same note states, and beside the worst residual reflection each choice leaves:
| Z0, supply | PU / PD | Table 1 RS | Worst |ρ|, Table 1 | Z0 − mean | Worst |ρ|, calculator |
|---|---|---|---|---|---|
| 35 Ω, 3.3 V | 49 / 45 Ω | 0 Ω | 0.167 | 0 (driver above Z0) | 0.167 |
| 35 Ω, 2.5 V | 62 / 67 Ω | 0 Ω | 0.314 | 0 (driver above Z0) | 0.314 |
| 50 Ω, 3.3 V | 45 / 42 Ω | 5 Ω | 0.031 | 6.50 Ω | 0.018 |
| 50 Ω, 2.5 V | 57 / 58 Ω | 0 Ω | 0.074 | 0 (driver above Z0) | 0.074 |
| 75 Ω, 3.3 V | 43 / 38 Ω | 10 Ω | 0.220 | 34.5 Ω | 0.026 |
| 75 Ω, 2.5 V | 51 / 49 Ω | 0 Ω | 0.210 | 25.0 Ω | 0.014 |
| 100 Ω, 3.3 V | 41 / 35 Ω | 12 Ω | 0.361 | 62.0 Ω | 0.015 |
| 100 Ω, 2.5 V | 49 / 44 Ω | 5 Ω | 0.342 | 53.5 Ω | 0.024 |
Where Z0 − Zout is a few ohms or less, the table and the rule agree. On the 75 Ω and 100 Ω lines they part: for 100 Ω at 3.3 V the rule asks for 62.0 Ω and the table proposes 12 Ω, leaving a reflection of 0.36. The note calls Table 1 "a basic value" and recommends signal-integrity simulation "with IBIS models ... to optimize the value of the series resistor by including the receiver and board parasitics", which may be where its smaller values come from; the page does not reproduce that simulation and follows the stated rule. Where the driver alone exceeds Z0, as on the 35 Ω line, no series resistor helps, and both give 0 Ω.
Thevenin pair: SNAA377's 130 Ω and 82 Ω
SNAA377 terminates a 50 Ω LVPECL line at VCC − 2 V from 3.3 V. Equations 1 and 2 solved exactly give 127 Ω and 82.5 Ω; the nearest E24 values are the note's own 130 Ω and 82 Ω, which its Equations 3 and 4 check as "≈ 50Ω" and "≈ 1.3V". The calculator gives 50.3 Ω and 1.28 V, and one more number the note leaves out: the pair draws 51.4 mW from the supply whether the line is switching or not.
AC termination: SNLA034's cable
SNLA034's example is 100 ft of 100 Ω cable at 1.7 ns/ft. "CT ≤ (100 ft × 2 × 1.7 ns/ft)/100Ω or ≤ 3,400 pF", and with the RC time constant held to 10 % of the unit interval "the maximum switching rate therefore should be less than 300 kHz". The calculator gives 3.40 nF, an RC of 340 ns and 294 kHz. It is a termination for slow control lines, which is how the note itself classes it.
What an unterminated line does
The figure's grey staircase is the same line with no termination. A strong driver makes it worse: 20 Ω into an open 50 Ω line launches 2.36 V, which doubles to 4.71 V at the receiver, then falls to 2.69 V one round trip later as the driver's mismatch inverts the returning wave, and only settles towards 3.3 V after several round trips. Change the driver impedances to see it.
Where the model stops
- Resistive impedances. The lattice treats the driver, line and terminations as resistances and the receiver as an open circuit. Receiver capacitance, package inductance and the driver's non-linear switching are what IBIS simulation adds.
- A lossless, uniform line. Vias, connectors and stubs are further reflection points; the calculator sees only the two ends.
- The mean of pull-up and pull-down. It is a choice, not something the notes state. When the two differ widely, one edge will be under- and the other over-terminated, and the residual reflections show by how much.
- Power is DC. The parallel and Thevenin figures are V²/R averages; the switching power of charging the line is not included.
Further reading
- TI SNLA027, AN-807 Reflections: Computations and Waveforms — the reflection coefficients (Equations 14 and 16, p. 6) and the lattice.
- TI SCAA080, CDCx706/x906 Termination and Signal Integrity Guidelines — series termination and Table 1 of driver impedances (§2, pp. 2–3).
- TI SNAA377, Termination Guidelines for Differential and Single-Ended Signals — the Thevenin pair (§3.1) and LVCMOS series termination (§4.1).
- TI SNLA034, AN-903 A Comparison of Differential Termination Techniques — parallel and AC termination (§4–5) and their costs.
- Clock termination — choosing between the schemes, and LVDS, LVPECL and HCSL.
- Critical length calculator — whether the line needs terminating at all.
- Microstrip impedance calculator — the Z0 to terminate to.