EMI input filter calculator: buck LC filter and damping
For 45 dB at 420 kHz with a 12 µH inductor, the filter capacitor must be at least 2.13 µF, damped by a capacitor of at least 38.5 µF with about 1.12 Ωof ESR. This calculator sizes a buck converter's differential-mode input filter by TI's AN-2162: the attenuation needed at the switching frequency, entered or estimated from the input current or a scope reading, the filter capacitor from Equations 4 and 5, and the damping branch. It then checks the capacitor you fit, and the filter's output impedance against the converter's input resistance.
Where the required attenuation comes from. Entered: the measured gap between your unfiltered fundamental and the limit, as SNVA755 does (45 dB). From the input current: AN-2162 Equation 3, the fundamental of a square-wave input current across C_IN. From a scope: Equation 2, the measured peak-to-peak ripple at f_s.
The attenuation the filter must give at f_s, in dB: the unfiltered fundamental from a LISN measurement less the limit. SNVA755 needs 45 dB to pass CISPR 22 Class B.
The lowest input voltage, in V. It sets the duty cycle, and the converter's input resistance V_in²/P_in is smallest there. AN-2162's examples use a 30 V minimum; SNVA755's board runs at 24 V.
The output voltage, in V. With the input it sets the buck duty cycle D = V_OUT/V_IN.
The DC inductor current, in A — for a buck, the output current (AN-2162 §4.1). Use the maximum: conducted EMI is worst at the highest input current.
The switching frequency, in kHz. The filter is designed at the fundamental, the worst case; its harmonics are attenuated more. 800 kHz and 370 kHz in AN-2162's examples, 420 kHz in SNVA755.
The converter's own input capacitance, in µF, "assumed to be a low ESR ceramic type" (AN-2162). Its impedance turns the switching current into the ripple voltage the filter attenuates. 2 × 10 µF in AN-2162 Example 1.
The filter inductor, in µH. AN-2162 puts it at 1 to 10 µH for low and medium power, SNVA755 at 1 to 20 µH: "Choose the highest value in compliance with amperage and physical size requirements." It must carry the full input current.
The inductor's DC resistance, in Ω, from its datasheet. It is the only loss in the undamped filter, so it alone sets how high the resonance peaks. 0.19 Ω for SNVA755's 12 µH part.
The capacitance you will fit, in µF — the calculation gives a minimum, the BOM a standard value. Enter 0 to see the filter with exactly the required value. SNVA755 fits 4.7 µF ∥ 0.22 µF.
Converter efficiency, %, for the input power P_in = V_OUT·I/η that sets the converter's input resistance. 100 % is the ideal case; a lossier converter draws more and its input resistance is lower.
- Duty cycle D = V_OUT/V_IN
- 0.208
- Required attenuation at f_s
- 45.0 dB
- C_fa, Equation 4 · C_fb, Equation 5
- 1.37 µF · 2.13 µF
- Filter capacitor C_f, at least
- 2.13 µF (C_fb: the attenuation sets it)
- With 4.92 µF fitted: corner
- 25.5 kHz (f_s/10 is 42.0 kHz)
- Attenuation at f_s, fitted stage
- 52.3 dB (+7.3 dB against the requirement)
- Damping capacitor C_d, Equation 6
- ≥ 38.5 µF, electrolytic, rated 25 % above the highest source voltage
- Damping resistance ESR_d, Equation 7
- ≈ 1.12 Ω
- Output impedance peak at V_B
- 6.66 Ω undamped at 14.8 kHz; 987 mΩ damped
- Converter input resistance |R_in| = V_in²/P_in
- 38.4 Ω (margin 15.2 dB undamped, 31.8 dB damped)
How this is calculated
Standard: TI SNVA489C, AN-2162 Simple Success With Conducted EMI From DC-DC Converters (rev. April 2013): §4, Equations 2–7, §5; TI SNVA755, Simple Success with Conducted EMI and Radiated EMI for LMR160X0 (June 2016): §2
- Equation 2 (p. 5), Method 1: a peak-to-peak ripple measured at the switching frequency with a wide-bandwidth scope, against the limit V_max in dBµV.
- Equation 3 (p. 5), Method 2: the first harmonic of a square-wave input current, (2I/π)·sin(πD), across the impedance 1/(2π·f_s·C_IN). I is the DC inductor current, the output current for a buck. D as V_OUT/V_IN is the first-order buck duty cycle; with V_IN(min) it reproduces the C_fb values AN-2162 §5 prints.
- Equation 4 (p. 6): "ensures that the resonance frequency of the EMI input filter is at least one decade below the switching frequency" — the resonance of L_f with C_f in series with C_IN. It has no positive solution when C_IN·L_f·(2πf_s/10)² ≤ 1.
- Equation 5 (p. 6), "derived from an approximation that ensures proper attenuation of the EMI filter". "Select the higher value of Cfa and Cfb because both conditions must be met."
- Equations 6 and 7 (p. 6). "The dc voltage rating of the electrolytic should be at least 25% larger than the worst case maximum source voltage."
- Derived from the circuit of AN-2162 Figure 4: the attenuation of the fitted stage, and the output impedance at V_B looking back toward a stiff source (C_f is then across the source and drops out). The damping term is present only for the damped curve. The peak is found numerically.
- Derived: a regulated converter draws constant power, so dI/dV = −P/V² at its input. The margin is 20·log(|R_in|/Z_out,peak). AN-2162 §7 lists Middlebrook and Erickson for the full stability treatment; no threshold is drawn here.
Assumptions
- Differential-mode conducted EMI of a non-isolated buck, the case AN-2162 and SNVA755 design for. Common-mode filtering is not covered.
- The input current is a square wave (the small-ripple approximation of AN-2162 Figure 5), and C_IN is a low-ESR ceramic, as Equation 3 assumes.
- The filter parts are ideal apart from the inductor's DCR: capacitor ESL, inductor self-resonance and the LISN's impedance are not modelled.
- The design is at the switching fundamental, the worst case; harmonics see more attenuation.
- The input-resistance comparison is a margin, not a stability proof. Check it at the lowest input voltage and highest load.
What it computes
A buck converter draws its input current in pulses, and the ripple those pulses make across the input capacitor is the conducted emission a compliance test measures. TI's AN-2162 (SNVA489) designs the differential-mode filter that stops it in four steps — "Calculate the required attenuation", "Select filter inductance Lf", "Calculate filter capacitance Cf", "Calculate damping capacitance Cd" — and SNVA755 runs the same procedure on a real board. The calculator does all four and then checks what AN-2162 only warns about: whether the filter's output impedance comes near the converter's input resistance.
The required attenuation is the height of the unfiltered fundamental above the limit at the switching frequency. Measured with a LISN, it is a number to enter. Before that, AN-2162 gives two estimates: Equation 2 converts a scope's peak-to-peak ripple into dBµV, and Equation 3 derives the fundamental from the input current itself, "extracting the first harmonic of current from the Fourier series of the input current waveform and multiplying that value by the impedance at the input port". The harmonics fall faster than the fundamental, so the fundamental is the design point.
The capacitor comes from two conditions, and AN-2162 is explicit: "Select the higher value of Cfa and Cfb because both conditions must be met." Equation 4 places the resonance of Lf with Cf and CIN "at least one decade below the switching frequency"; Equation 5 is "an approximation that ensures proper attenuation". Which one wins depends on the design, and the three published examples split: Equation 4 sets AN-2162's two, Equation 5 sets SNVA755's.
Worked example: SNVA755's LMR160X0 filter
The calculator's defaults, from SNVA755 §2: 24 V to 5 V at 3 A, switching at 420 kHz with 9.62 µF of input capacitance, and 45 dB required "in order to pass CISPR 22 Class B". The inductor is the 1234AS-H-120M, 12 µH and 0.19 Ω.
Required attenuation SNVA755, CISPR 22 Class B = 45 dB C_fa (4) 9.62 µF / (9.62 µF·12 µH·(2π·42 kHz)² − 1) = 1.367 µF C_fb (5) (1/12 µH)·(10^(45/40) / (2π·420 kHz))² = 2.128 µF C_f the higher = 2.128 µF Fitted 4.7 µF ∥ 0.22 µF = 4.92 µF Corner 12 µH with 4.92 µF in series with 9.62 µF = 25.5 kHz At 420 kHz |V_A/V_B| with 0.19 Ω DCR = 52.3 dB C_d (6) 4 × 9.62 µF ≥ 38.5 µF ESR_d (7) √(12 µH / 9.62 µF) ≈ 1.12 Ω Z_out peak undamped · damped = 6.66 Ω · 987 mΩ |R_in| 24² / (5 V × 3 A) = 38.4 Ω
SNVA755 prints Cfa = 1.37 µF and Cfb = 2.1 µF, which the equations reproduce, and fits 4.92 µF — more than twice the requirement, and 7.3 dB more attenuation than asked for. It also leaves the damping capacitor out: "in order to reduce the cost, no electrolytic is used". The impedance lines show what that costs: an undamped peak of 6.66 Ω set only by the inductor's DCR, 15 dB below the converter's 38.4 Ω input resistance at full load. With the branch AN-2162 prescribes it would be 987 mΩ.
The three published designs, reproduced
| Design | Attenuation | C_fa | C_fb | Required | Fitted |
|---|---|---|---|---|---|
| AN-2162 Example 1, LMZ23605 | 36.2 dB printed 40 dB | 4.93 µF printed 4.9 µF | 2.55 µF printed 2.5 µF | 4.93 µF | 4.7 µF |
| AN-2162 Example 2, LMZ14202 | 42.6 dB printed 40 dB | 8.34 µF printed 8.3 µF | 6.40 µF printed 6.4 µF | 8.34 µF | 10 µF |
| SNVA755, LMR160X0 | 45.0 dB printed 45 dB | 1.37 µF printed 1.37 µF | 2.13 µF printed 2.1 µF | 2.13 µF | 4.7 ∥ 0.22 µF |
Every printed capacitor value is reproduced, but AN-2162's two tables hide one step. They give the estimated noise as "≈ 80 dBµV" and the required attenuation as 40 dB, and Cfb at a flat 40 dB would be 3.96 µF and 4.74 µF — neither printed value. The printed Cfb of 2.5 µF and 6.4 µF come from Equation 3's unrounded attenuation, 36.2 dB and 42.6 dB, with the duty cycle taken as 3.3 V / 30 V. The table's 40 dB is the rounded target; the column beside it was computed from the equation. The calculator, in the input-current mode, follows the column.
The fitted values disagree with the rule in both directions. Example 1 fits 4.7 µF against a calculated 4.9 µF, a little under Cfa; Example 2 fits 10 µF against 8.3 µF. A standard value one step below the requirement moves the corner slightly above fs/10, which the attenuation line shows the cost of: 0.43 dB at 800 kHz for Example 1, against 5.2 dB of margin over Equation 3's requirement.
Filter capacitor by inductor, SNVA755's operating point
45 dB at 420 kHz with 9.62 µF of CIN. Below 1.49 µH no capacitor can satisfy Equation 4, because Lf with CIN alone already resonates above fs/10; the calculator says so rather than return a negative capacitance. The 12 µH row is the worked example.
| L_f | C_fa (4) | C_fb (5) | C_f, at least | ESR_d (7) |
|---|---|---|---|---|
| 2.2 µH | 20.30 µF | 11.61 µF | 20.30 µF | 478 mΩ |
| 4.7 µH | 4.48 µF | 5.43 µF | 5.43 µF | 699 mΩ |
| 6.8 µH | 2.71 µF | 3.76 µF | 3.76 µF | 841 mΩ |
| 10 µH | 1.69 µF | 2.55 µF | 2.55 µF | 1.02 Ω |
| 12 µH | 1.37 µF | 2.13 µF | 2.13 µF | 1.12 Ω |
| 15 µH | 1.06 µF | 1.70 µF | 1.70 µF | 1.25 Ω |
| 22 µH | 0.70 µF | 1.16 µF | 1.16 µF | 1.51 Ω |
Read down the table and the trade AN-2162 describes is visible: a bigger inductor needs less capacitance on both counts, which is why its advice is to "Choose the highest value in compliance with amperage and physical size requirements". The damping resistance rises with it, as √(Lf/CIN).
Damping and the converter's input resistance
The resonance the filter is built around does not disappear because it sits a decade below fs. AN-2162 §4.4 is about its other effect: "The output impedance of the filter must be sufficiently small at point VB so that input filter does not significantly affect the loop gain of the SMPS", and damping "is needed when the output impedance is very high at the resonant frequency (that is, Q of filter formed by CIN and Lf is too high.)" The calculator computes that impedance — (DCR + jωLf) ∥ CIN, looking back from VBtoward a stiff source, so Cf drops out — with and without the branch of Equations 6 and 7 across it.
What it is compared with is derived rather than quoted. A regulated converter holds its output power constant, so its input current falls as its input voltage rises, and incrementally its input looks like a negative resistance of magnitude Vin²/Pin. AN-2162's references list Middlebrook's "Design Techniques for preventing Input Filter Oscillations in Switched-mode regulators" and Erickson's work on input-filter damping for the full treatment; the calculator reports the margin between the peak and that resistance in dB and does not draw a pass line of its own. Check it at the lowest input voltage and highest load, where Vin²/Pin is smallest.
Where the model stops
- Differential mode only. AN-2162 and SNVA755 design for a non-isolated converter's two-wire input, where "the common mode noise VCOMM will always be zero". A converter with a safety-ground path needs a common-mode filter as well.
- The square-wave current is an approximation.Equation 3 assumes small inductor ripple (AN-2162 Figure 5), and the duty cycle here is VOUT/VIN, losses ignored.
- Ideal parts above the corner. The stage's attenuation ignores the capacitor's ESL and the inductor's self-resonance, which cap what any real L-C gives at high frequency, and the LISN's impedance, which the test puts on the source side.
- The damping branch is AN-2162's prescription, not an optimum. Cd = 4·CIN and ESRd = √(Lf/CIN), with the electrolytic rated "at least 25% larger than the worst case maximum source voltage".
Further reading
- TI SNVA489, AN-2162 Simple Success With Conducted EMI From DC-DC Converters — the procedure (§3), Equations 2 to 7 (§4), the two worked designs (§5) and the LISN (§6).
- TI SNVA755, Simple Success with Conducted EMI and Radiated EMI for LMR160X0 — the same procedure on the LMR160X0 board (§2), with measured results, and layout for radiated EMI (§3).
- Buck converter input filter design for conducted EMI — the harmonics, the LISN, the damped and undamped impedance, and layout.
- Ferrite bead filter calculator — the same resonance between a series element and a shunt capacitor, for a bead.
- Buck ripple calculator — the input and output ripple of the converter the filter sits in front of.